Display MoreHey Jeff, would you please be kind enough to scroll down to my post on issues with the Q400 paint kit, and see if there is any thing that you could advise to correct the issues? Any thing that you could offer would be greatly appreciated. Thank you!
Q400 Paint Kit help needed please
Thank you!
Kerry
Let me look into it for you.
finally figuered it out how to do the engines. now shes sitting out side drying off lol.
Excellent! She looks beautiful. Trying to get straight lines down the fuselage on the 737 is a real challenge. I have spent a lot of hours on my first 737 scheme and still have a lot to go.
thanks very mutch . it was a night mare to do but she is looking good. hope to see your soon mate.
finally figuered it out how to do the engines. now shes sitting out side drying off lol.
I'm stuck at the same point now. What did you do to make this work?
Jay, just deactivate the CaliforniaOne layer activated on the Engine_Left_Right_Color texture then export the texture.
it is deactivated..
yer just deactivate the layer then save it as bmp 24 bit then re run the conversion
I'tried this five times already..
California engines only
Deactivated right?
which layer did you use for the main colour of engines?
Jay,
It is possible that you may have inadvertently duplicated the California_One layer at a higher priority position. If you have, then you would still see the livery even with the standard California_One deactivated. My next step if I were in your position would be to systematically check every layer with a higher priority to be sure that you don't have one hiding..
When you export the 24 bit .bmp prior to compiling the model, is the California_One livery showing on the exported .bmp?
Jay, a few things I've been thinking about... First, I forgot to answer your question...I always create a new folder in the Liveries area for each repaint that I do. So just as you now have the California_One folder, I would create a folder in the Liveries section, and place all of your layers for your repaint within that folder. Second, could you show us what the .bmp file for the engines looks like before you compile the project? That might provide some clues as to what is driving the issue.
ok jay im doing a video tutorial for you ill upload it at 12pm today for you.
Thanks for your attention guys. It's really curious issue though. All the other textures are fine, just this damn engines.
The exported BMP is showing no traces of California however preview and the model itself does.
yer delete the preview picture in the file before you convert then convert it again
ok jay . the psd file for photo shop for the engines say engines_left_right_color . what i did was duplicate it and rename one to engine_left_color then the other one rename it engine_right_color .then put them in the folder instead off engine_left_right_color.then paint them and convert them.hope that helps.
like this aerofly.com/community/index.php?attachment/12494/
with the repaint tmr is well. then paint it save the bmp files then convert it . hope that helps
ok jay . the psd file for photo shop for the engines say engines_left_right_color . what i did was duplicate it and rename one to engine_left_color then the other one rename it engine_right_color .then put them in the folder instead off engine_left_right_color.then paint them and convert them.hope that helps.
This might be it man!
I'll give it a shot when I get back from work.
How did you figure this out? 
Ps
The link above is blank.
took me a while but it works lol. i just noticed that the psd file for the engines was for both so i fort i split them up then convert and it worked .
Vital information guys
Thank you all..
finally figuered it out how to do the engines. now shes sitting out side drying off lol.
Dry yet? 
Edit:
Thank you for sharing your work!
Iv done jet2 737 now . it will be uploaded on https://flight-sim.org/filebase/ later today. My easyjet is on there now to have .
