Thanks Sir, But at what Altitude is it cruising?
about 3000ft
Thanks Sir, But at what Altitude is it cruising?
about 3000ft
brunnobellic I searched it too, but I didn't find it, is it moving in like a circle, or is it moving in a straight line and then spawning to its start position?
Before I've had problems with the animations, for example, the Zurich animation didn't work, I had to remove all other animations from places folder and I did the same this time but it still doesn't work
It moves in a straight line for a long time then come back down and repeated.
I still can't find it
About 5 minutes after starting the scenery, I found the tanker at this position.
I still can't find it
Did you contact ATC?
Your best bet is to use the DEV Cam in order to find it first.
Did you contact ATC?
Your best bet is to use the DEV Cam in order to find it first.
I tried to look for it with the developer camera and I didn't find it, developer camera moves so fast and the plane would be so small to find.
About 5 minutes after starting the scenery, I found the tanker at this position.
I went to the exact location and it was empty.
I also looked into tm.log file and I'm not sure it even loaded it, because I searched ''dc10'' from there and it didn't find it.
I tried to look for it with the developer camera and I didn't find it, developer camera moves so fast and the plane would be so small to find.
I went to the exact location and it was empty.
I also looked into tm.log file and I'm not sure it even loaded it, because I searched ''dc10'' from there and it didn't find it.
Exactly! Same for me as well. I searched Every Direction of the specified Location but Failed to Spot the Tanker..
Thanks for the quick response on DEV cam - very useful. I really can't find the tanker for sure now - hard to know how to start precisely - but when I move north/south of my starting point quite a bit, I don't see the tanker dc-10. I have it in Documents/Aerofly FS2/scenery/places
For those of us that can't find it, maybe our installation is somehow wrong.. - When I look through the tm.log, I don't see any mention of kc10 - I see FS2 looking through addons but not scenery/places?
TomSimMuc, how about a picture where both (F-18 and DC-10) are near each other at the very beginning after startup.
Thanks for the quick response on DEV cam - very useful.
You're welcome!
THANKS Lucas that's a very interesting camera mode. Cheers Michael.
Yes it's a movie camera, I'm going to make several flights with the cinematographic camera that is my favorite.
Tip: Try to lock the camera in the place close to where Brunno is positioned, wait a few minutes, pause the Simulator and move the Replay bar faster until you notice a gray movement, increase the screen contrast so that it can be easier to locate the plane.
Edit: Positioning the camera just above the water and focusing upwards and zooming out can also help you notice movement!
I'm just using it to look and test my scenery, cheers
how about a picture where both (F-18 and DC-10) are near each other at the very beginning after startup.
You are welcome:
Thanks much for the help - now for the weird part - I moved to your precise location and I saw the kc10 - flew into contact position - and then restarted and I don't see the kc10 now. There is something about my config ( and perhaps addons and their locations ) that is nonrepeatable. Wasn't there a big change to either TSC files and naming conventions or something that I might have missed. TBH, I haven't flown FS2 at any addon location for a while - just focused on "official DLC". Maybe I have some addon scenery that messes up other things like kc10??
TomSimMuc Oh yes, now I've finally found it too, It was like searching for a needle in the sky, it's really hard to fly close to its fuel hose, but thanks anyway!
And thank you very much brunnobellic for this awesome addon!
It's really fun to fly in formation with it