aircraft:tmd:inputs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
aircraft:tmd:inputs [2019/07/20 17:09] – jh | aircraft:tmd:inputs [2022/07/19 21:00] – jh | ||
---|---|---|---|
Line 22: | Line 22: | ||
E.g. you don't need to come up with different names for the graphics section than for the physics. Just re-use the same one everywhere. Much easier. | E.g. you don't need to come up with different names for the graphics section than for the physics. Just re-use the same one everywhere. Much easier. | ||
- | E.g. In the GraphicObjects section you can **re-use the same name for the graphic object**, e.g. the hingedbodygraphics LandingLightSwitch can use the AngleID | + | E.g. In the GraphicObjects section you can **re-use the same name for the graphic object**, e.g. the hingedbodygraphics LandingLightSwitch can use the InputID |
**...Knob, ...Switch** | **...Knob, ...Switch** | ||
Line 79: | Line 79: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 107: | Line 107: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
- | < | + | |
> | > | ||
</ | </ | ||
Line 207: | Line 206: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 236: | Line 235: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
> | > | ||
</ | </ | ||
Line 277: | Line 276: | ||
The typical chain consists of '' | The typical chain consists of '' | ||
- | The setup is similar to the toggle switch only with minor differences like the use of '' | + | The setup is similar to the toggle switch only with minor differences like the use of '' |
=== ControlObjects === | === ControlObjects === | ||
Line 329: | Line 328: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 362: | Line 361: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
> | > | ||
</ | </ | ||
Line 431: | Line 430: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 464: | Line 463: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
> | > | ||
</ | </ | ||
Line 528: | Line 527: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 553: | Line 552: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
> | > | ||
</ | </ | ||
Line 612: | Line 611: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 644: | Line 643: | ||
< | < | ||
< | < | ||
- | < | + | < |
- | < | + | < |
> | > | ||
</ | </ | ||
Line 654: | Line 653: | ||
< | < | ||
- | < | + | < |
- | < | + | < |
< | < | ||
< | < | ||
Line 668: | Line 667: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 677: | Line 676: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 698: | Line 697: | ||
< | < | ||
- | < | + | < |
< | < | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 718: | Line 717: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 733: | Line 732: | ||
< | < | ||
- | < | + | < |
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 755: | Line 754: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 763: | Line 762: | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 777: | Line 776: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 792: | Line 791: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 812: | Line 811: | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 837: | Line 836: | ||
< | < | ||
- | < | + | < |
- | < | + | < |
< | < | ||
< | < | ||
Line 846: | Line 845: | ||
> | > | ||
< | < | ||
- | < | + | < |
- | < | + | < |
< | < | ||
< | < | ||
Line 870: | Line 869: | ||
< | < | ||
- | < | + | < |
< | < | ||
> | > | ||
< | < | ||
- | < | + | < |
< | < | ||
< | < | ||
Line 883: | Line 882: | ||
Outputs 1.0 to the tmd as long as a lever is grabbed or a button is depressed. | Outputs 1.0 to the tmd as long as a lever is grabbed or a button is depressed. | ||
+ | |||
+ | > Typically this is only used to make a light illuminate as long as a button is pressed or to give visual feedback that a control is grabbed. Don't use this for every single button in combination with an event_edge, this should be done with the '' | ||
< | < | ||
- | < | + | < |
< | < | ||
> | > | ||
</ | </ | ||
aircraft/tmd/inputs.txt · Last modified: 2022/07/19 21:02 by jh