You can assign aileron and elevator trim which also work for the cyclic input. I'll note down this suggestion though
Posts by Jet-Pack (IPACS)
-
-
Thanks for the suggestions, these have all been suggested by other users though, please stay in the respective threads and avoid double posting.
-
Das Problem ist dass die dahinter liegende Landschaft in "unendlicher Entfernung" dargestellt wird. Somit sieht das Modell immer dichter aus als der Boden. Bei steilen Hängen fällt das nicht so auf, da der Schatten eh wo anders hinfällt aber eben nicht direkt unter das Modell. Das ist eine Limitierung durch das Panoramabild, das nur an einer festen Stelle aufgenommen werden kann. Es ist physikalisch nicht möglich den nötigen Abstand zwischen den Augen mitzuspeichern in einem festen Bild.
-
And tomorrow ... of a possible Aerofly FS 3, is this on your list Jan, or are fictitious speculation?
We are not ruling out a new version in the future but for now we are still developing Aerofly FS 2 further.
-
We have had this request several times in the past and explained why we currently only have the -500 model in the sim.
-
Dont worry, I move the other thread over here.
-
Can you please show us a screenshot?
-
So what do you see on your device?
-
Obviously a Mac problem
The default aircraft files are identical for mac or windows. The operating system is usually not an issue unless the creator used upper case file or folder names or spaces in the file or folder names.
-
Ok, what setup do you want to create and what prevents you from connecting the hardware directly to the computer that runs Aerofly?
I'm not fully understanding the question, please elaborate further.
-
8192 per tile I think. But I'd have to ask the 'the boss' (a.k.a. admin )
-
don't work on rc8. No FunCub in the list.
Aircraft only show up when they are correctly installed. Please check your folder structure.
-
IPACS has created many flight simulators in the past and to my knowledge it has always been flight simulation.
We started with radio control flight simulators that we are still producing to the present day.
Product names that come to mind: Easyfly 1, 2, 3, 4, Aerofly Professional (+Deluxe), Aerofly RC 5, 7 and Aerofly RC 8.
We branched out to full scale flight simulators with the Aerofly FS 1 and are working on Aerofly FS 2 till today.
-
Ok, I've had enough of these threads. Sorry but if you open any more threads with this same question you're getting banned.
We already have plenty of similar threads where you can write to.
From my understanding you are trying to get a reply from other users for when they want to expand their scenery. If this question is directed at us, please elaborate.
-
TOGA = takeoff go around thrust. You cannot "perform a TOGA".
As I said, the aircraft automatically activates full thrust if you fly too slow. This is only active above 100ft above the ground though. You can't activate this on the ground. As he said: he was about to land when it happened. He then got too slow which triggered the maximum thrust "A.FLOOR" safety function similarly to how it would have in the real world.
-
I see a lot of missing textures and invalid texture entries. Towards the end there is a warning that more than 8192 trees are added and from that point forward there are more errors and warnings. I'm guessing there could be a region that has too many trees.
-
The Alpha Floor function applies full TOGA thrust regardless of your initial thrust lever position to prevent a stall. Most of the time the fly by wire will add a gentle nose to prevent the stall. But if you keep pulling or if the angle of attack gets too high, then it adds full thrust.
You can cancel that with the red button on the thrust levers or by pulling the thrust levers to idle. In case your levers already were at idle just move them a bit forward and then back to idle to disable the autothrust.
-
Same issue here - crashes repeatedly in Vulkan, but rock-steady in OpenGL.
What was the cause of the crash according to the tm.log?
-
If you're a programmer, we're also hiring.
-
Jup. You can also try and extend the first flap position at high speed and it won't let you do that either.